•   Call Us: +212 (0) 691 660 672
  •  contact@smmrmaroc.ma

Polype endométrial et hypofertilité : quels niveaux de preuve ?

Jul 11 2014 Rédaction

Le polype endométrial est une lésion hyperplastique localisée de l’endomètre, considérée comme l’une des plus fréquentes pathologies gynécologiques. Cependant, sa physiopathogénie est encore incomplètement élucidée, même si diverses anomalies biomoléculaires associées ont été récemment rapportées. Il peut entraîner des saignements anormaux, des douleurs et une infertilité. Son diagnostic a bénéficié des progrès de l’imagerie, mais l’hystéroscopie reste l’examen de référence. Son incidence varie selon l’âge, les symptômes et les critères diagnostiques retenus. L’association des polypes à l’infertilité ne manque pas de susciter de nombreuses questions. Une étude réalisée chez un primate confirme l’impact du polype sur la fertilité. Les données épidémiologiques montrent que les EP sont fréquents chez la femme infertile, avec une incidence variable selon le contexte clinique. Elle est encore plus élevée chez les patientes présentant une endométriose. Divers mécanismes tendant à expliquer l’altération de la fertilité ont été proposés, le plus pertinent semble être l’altération de la réceptivité endométriale. Les données thérapeutiques, longtemps limitées à des études observationnelles, sont aujourd’hui un peu plus consistantes, suggérant l’amélioration des performances reproductives après polypectomie. Finalement, compte tenu de l’innocuité de cette intervention, il paraît légitime de proposer son utilisation en cas de polype identifié chez une femme infertile, en particulier dans le contexte d’une assistance médicale à la procréation ; néanmoins, le niveau de preuve est encore limité, justifiant la réalisation d’études contrôlées rigoureuses.

Read 46615392 times
Rate this item
(2 votes)

About The Author

85038 comments

  • Alicia Reddin
    Comment Link Alicia Reddin Friday, 02 October 2026 04:20

    The Label: The printed graphic on the very top of the disc.

  • Pedro Hulet
    Comment Link Pedro Hulet Friday, 02 October 2026 04:20

    When a disc fails, it is usually due to one of three main problems:

  • Arlie Constanzo
    Comment Link Arlie Constanzo Friday, 02 October 2026 04:20

    website: https://repaircddvd.com

  • Cassaundra Halling
    Comment Link Cassaundra Halling Friday, 02 October 2026 04:20

    Most disc reading issues happen because the clear polycarbonate plastic layer gets scratched. The laser in your computer drive needs to pass through this plastic cleanly, bounce off the internal metallic layer, and reflect back to a sensor. If the plastic is scratched, the laser gets refracted and scattered—like a car headlight hitting thick fog. The drive cannot read the data below, even though the data itself is perfectly intact.

  • Jess Ahlf
    Comment Link Jess Ahlf Friday, 02 October 2026 04:20

    website: https://repaircddvd.com

  • Jaimee Griep
    Comment Link Jaimee Griep Friday, 02 October 2026 04:20

    Understanding the Anatomy of Optical Disc Failure

  • Jerrold Loreaux
    Comment Link Jerrold Loreaux Friday, 02 October 2026 04:20

    Sometimes the physical disc looks pristine, but the data structure inside is broken. If a multi-session disc was not finalized correctly during burning, or if the Master Boot Table (the index that tells the computer where each file starts and ends) becomes corrupted, standard operating systems will see the disc as blank, empty, or unformatted.

  • Sunday Berbereia
    Comment Link Sunday Berbereia Friday, 02 October 2026 04:20

    Often referred to as "disc rot" or oxidation, this happens when oxygen and moisture penetrate the protective lacquer layer and cause the internal aluminum film to corrode. It usually looks like tiny pinholes or dark bronze discoloration when you hold the disc up to a light source.

  • Queenie Mcelvany
    Comment Link Queenie Mcelvany Friday, 02 October 2026 04:20

    Sometimes the physical disc looks pristine, but the data structure inside is broken. If a multi-session disc was not finalized correctly during burning, or if the Master Boot Table (the index that tells the computer where each file starts and ends) becomes corrupted, standard operating systems will see the disc as blank, empty, or unformatted.

  • Shera Torrado
    Comment Link Shera Torrado Friday, 02 October 2026 04:20

    Often referred to as "disc rot" or oxidation, this happens when oxygen and moisture penetrate the protective lacquer layer and cause the internal aluminum film to corrode. It usually looks like tiny pinholes or dark bronze discoloration when you hold the disc up to a light source.

Leave a comment

Make sure you enter all the required information, indicated by an asterisk (*). HTML code is not allowed.